Runways at FYMG
According to OurAirports data (compiled from AIP and FAA sources), Midgard Airport has one runway: 02/20 - 1,472 m long (4,828 ft), 10 m wide, unpaved surface.
Namibia · elevation 5125 ft AMSL
· -22.0106, 17.3700
Midgard Airport is an airport with the ICAO code FYMG and the IATA code MQG. Country: Namibia. Nearest settlement listed in the database: Midgard. OurAirports classifies it as a small airport. Its ICAO code starts with the FY prefix, which marks airports in Namibia. The four-letter code FYMG is used in flight operations and weather reports, while the three-letter IATA code MQG is used for ticketing and baggage handling. The airport reference point sits at 22°00'38"S, 17°22'12"E, at an elevation of 5,125 ft (1,562 m) above sea level. The applicable time zone is Africa/Windhoek.
Aerial imagery showing the runway and apron layout - the zoom is matched to the longest runway.
| Threshold | Course | Length | Width | Surface |
|---|---|---|---|---|
| 02 | 20° | 1,472 m (4,828 ft) | 10 m (33 ft) | unpaved |
| 20 | 200° |
The course is derived from the runway designator (number × 10), not from a survey - the actual magnetic bearing can differ by a few degrees.
Declared distances (TORA, TODA, ASDA, LDA) are published in the national AIP - they are not part of this table.
According to OurAirports data (compiled from AIP and FAA sources), Midgard Airport has one runway: 02/20 - 1,472 m long (4,828 ft), 10 m wide, unpaved surface.
The thresholds are oriented as follows: 02/20 on 20° and 200° magnetic. A threshold designator is its magnetic heading divided by ten (ICAO Annex 14), so the runway axis can be read straight off the numbers.
For the 02/20 axis, wind from the east (around 110°) or from the west (around 290°) blows perpendicular to the runway and produces the largest crosswind component. Wind from around 20° or 200° acts along the runway, as a headwind or a tailwind. The decoder on this page computes those components automatically from the current METAR.
Weather reports for Midgard Airport are published under the ICAO code FYMG. A METAR is an observation of current conditions, usually issued every 30 or 60 minutes; a TAF is a forecast for the airport area, typically covering 9 to 30 hours.
The decoder breaks the FYMG report down into its parts: wind direction and speed including gusts and variability, visibility (including CAVOK and directional minimum visibility), weather phenomena by WMO code, cloud layers with their bases, temperature and dew point, QNH pressure, and the resulting flight category - VFR, MVFR, IFR or LIFR - using FAA thresholds.
Not every airport issues its own reports; many smaller airfields have no weather station. If no current data is available for FYMG, check the nearby airports listed below.
Reports always use UTC (the Z suffix). The Africa/Windhoek zone stays at GMT+02:00 year-round, so converting to local time is always the same shift.
The closest airports in the database, measured in a straight line from the reference point, are Osona Airstrip (FYSN, 42 km), Okahandja Airstrip (FYON, 49 km), Hosea Kutako International Airport (Windhoek) (FYWH, 53 km). When no report is available for FYMG, they usually give the best approximation of conditions in the area.
METAR Academy
Step-by-step guides - with examples, charts and calculators.
Advertisement
Pass your ICAO Aviation English exam - 100% online
ICAO Level 4, 5 or 6 for PPL(A)/CPL(A)/ATPL(A): aviation vocabulary, radio phraseology, pronunciation and standard/emergency flight scenarios. Buy through this link and get a 10% discount.
Advertisement

VFR Map Europe - your aeronautical chart in the cockpit
Moving GPS map, airspace and zones, airspace alerts and offline use. Plan your VFR route online for free and send it to the app. The online map is free.
Check VFR MapRun a flying club, a training organisation or an airfield website? Embed a ready-made panel with the current FYMG METAR - flight category, wind, visibility, temperature and pressure, refreshed automatically. The configurator lets you pick language, theme and units; you paste the code once.