Runways at KMPG
According to OurAirports data (compiled from AIP and FAA sources), Marshall County Airport (Moundsville) has one runway: 06/24 - 1,006 m long (3,301 ft), 18 m wide, asphalt surface.
United States · elevation 1214 ft AMSL
· 39.8808, -80.7358
Marshall County Airport (Moundsville) is an airport with the ICAO code KMPG. Country: United States. Nearest settlement listed in the database: Moundsville. OurAirports classifies it as a small airport. Its ICAO code starts with the KM prefix, which marks airports in United States. No IATA code is assigned, which is typical for airports without scheduled traffic. The airport reference point sits at 39°52'51"N, 80°44'09"W, at an elevation of 1,214 ft (370 m) above sea level. The applicable time zone is America/New_York.
Aerial imagery showing the runway and apron layout - the zoom is matched to the longest runway.
| Threshold | Course | Length | Width | Surface |
|---|---|---|---|---|
| 06 | 60° | 1,006 m (3,301 ft) | 18 m (60 ft) | asphalt |
| 24 | 240° |
The course is derived from the runway designator (number × 10), not from a survey - the actual magnetic bearing can differ by a few degrees.
Declared distances (TORA, TODA, ASDA, LDA) are published in the national AIP - they are not part of this table.
According to OurAirports data (compiled from AIP and FAA sources), Marshall County Airport (Moundsville) has one runway: 06/24 - 1,006 m long (3,301 ft), 18 m wide, asphalt surface.
The thresholds are oriented as follows: 06/24 on 60° and 240° magnetic. A threshold designator is its magnetic heading divided by ten (ICAO Annex 14), so the runway axis can be read straight off the numbers.
For the 06/24 axis, wind from the south-east (around 150°) or from the north-west (around 330°) blows perpendicular to the runway and produces the largest crosswind component. Wind from around 60° or 240° acts along the runway, as a headwind or a tailwind. The decoder on this page computes those components automatically from the current METAR.
Weather reports for Marshall County Airport (Moundsville) are published under the ICAO code KMPG. A METAR is an observation of current conditions, usually issued every 30 or 60 minutes; a TAF is a forecast for the airport area, typically covering 9 to 30 hours.
The decoder breaks the KMPG report down into its parts: wind direction and speed including gusts and variability, visibility (including CAVOK and directional minimum visibility), weather phenomena by WMO code, cloud layers with their bases, temperature and dew point, QNH pressure, and the resulting flight category - VFR, MVFR, IFR or LIFR - using FAA thresholds.
Not every airport issues its own reports; many smaller airfields have no weather station. If no current data is available for KMPG, check the nearby airports listed below.
Reports always use UTC (the Z suffix). The America/New_York zone is GMT-05:00 in winter and GMT-04:00 in summer - that is the shift to apply to the time in the report to get local time at the airport.
The closest airports in the database, measured in a straight line from the reference point, are Wheeling Ohio County Airport (KHLG, 34 km), Washington County Airport (KAFJ, 47 km), Greene County Airport (Waynesburg) (KWAY, 52 km). When no report is available for KMPG, they usually give the best approximation of conditions in the area.
METAR Academy
Step-by-step guides - with examples, charts and calculators.
Advertisement
Pass your ICAO Aviation English exam - 100% online
ICAO Level 4, 5 or 6 for PPL(A)/CPL(A)/ATPL(A): aviation vocabulary, radio phraseology, pronunciation and standard/emergency flight scenarios. Buy through this link and get a 10% discount.
Advertisement

VFR Map Europe - your aeronautical chart in the cockpit
Moving GPS map, airspace and zones, airspace alerts and offline use. Plan your VFR route online for free and send it to the app.The online map is free.
Check VFR MapRun a flying club, a training organisation or an airfield website? Embed a ready-made panel with the current KMPG METAR - flight category, wind, visibility, temperature and pressure, refreshed automatically. The configurator lets you pick language, theme and units; you paste the code once.